IPL/OPT Photon Cosmetology...-manufacture,factory,supplier from China

A photon is an fundamental particle, a quantum of electromagnetic radiation. In quantum subject theory, it is the pressure provider that transmits the electromagnetic force.Light spots/spots are few and a ways betweenLight spot is the contact factor of mild contact skin, distinctive units have specific mild output measurement and shape.

Optical terms for cosmetic instrumentsA photon is an elementary particle, a quantum of electromagnetic radiation. In quantum field theory, it's the force carrier that transmits the electromagnetic force.Light spots/spots are few and far betweenLight spot is the contact point of light contact skin, different instruments have different light output size and shape. Such as color light instrument contact point is generally rectangular, size marked as long x wide (for example: 10mm x 25mm). Generally, the laser output is a dot, and the size is marked as the diameter (e.g., 3mm, 8mm, etc.).

Along with the continuous development of economy in our country, most areas begin to produce electric power equipment, which makes the national grid electric power output insufficient, coupled with the aging of the power output facilities, eventually causes the voltage at the end of the circuit to be too low, which brings great influence on the stability of laser output. The stable output of laser energy is a necessary condition for laser production.

Selection and use of semiconductor laser power supplyFirst, the basic requirements of semiconductor laser power supply1. Constant current output: short-circuit constant current output, load changes or short-circuit automatic adaptation.2. Output current ripple: ripple, noise and rated output current cannot exceed the maximum current that the laser tube can bear.3. Output voltage ripple: Ripple voltage noise will not damage the laser immediately, but if serious, it will affect the life of the laser.4. Soft start: Slow start current curve, no overshoot.5.

Laser power supply is the energy of laser, it provides pumping energy to laser, control laser output strength and repetition frequency. Therefore, laser power supply is an essential part of laser. Its power and stability have direct influence on the corresponding performance of laser. The current output of a power box is designed according to the requirements of the pump module.

Laser cutting machine equipment common faults and solutions1, boot without any response▶ Power fuse is burnt out: Replace the fuse.▶ Power input is normal: Check power input and make it normal.▶ Main power switch is damaged: Replace the main power switch.2, no laser output or very weak laser▶ Optical path offset: Carefully adjust the optical path.▶ Contaminated or damaged reflector lens: Clean or replace reflector lens.▶ Whether the focal length of the device is changed: readjust the focal length.▶ Focusing mirror is contaminated: Clean the focusing mirror.▶ Cooling water quality or temperatur

Switch power output protection policyIn all switching power supply designs, protection against load and protection against power supply due to load failure is a very important aspect to be considered in the design. In the design of military products, a kind of work called failure mode and impact analysis is often required. In this work, each part of the circuit is assumed to be an open circuit fault and then a short circuit fault. In this case, analyze separately how each fault will affect the rest of the circuit.

Classification of switching power suppliesSwitching power supplies can be divided into AC/DC and DC/DC. As a secondary power supply, DC/DC converter has realized modularization, and the design technology and production process have been mature and standardized at home and abroad, and has been recognized by users. However, due to its own characteristics, the primary power AC/DC has encountered more complex technical problems and manufacturing problems in the process of modularization.

How to use high voltage power supply to detect high voltage cablesTo ensure the normal and safe use of high-voltage cables, check the cable inlet before or after using them for a period of time. The test includes determining whether the main insulation is damp or aging, and checking whether there are defects in the main insulation of the cable after the voltage test. High voltage power supply is the main tool used for voltage resistance and insulation detection of cable.The source of Radium specially produced a power supply type for the high voltage test of power supply :HY-12KV and HY-32KV.

The basic principle of PWM switching power supplyAlthough pulse-width-modulated (PWM) switching power supplies have been around for a long time, they were not widely accepted and used until the mid-1970s. Switching power supplies have many advantages over linear power supplies.For the same power capacity, switching power supplies are more efficient and smaller than linear power supplies, but the design is more complex and electromagnetic interference (EMI) is more severe.There are two approaches to the current design of switching power supplies.